Technical Data
High Pressure Material Pressure Regulator
ไทย
Manage the pressure flow for multi high pressure spray gun within 1 feeding unit
The high pressure spray gun receive the pressure flow from feeding unit in order to make spraying. In case of automatic spray gun or manual gun, the single unit of spray gun does not have the pressure inconsistent because there have only 1 way flow.
In other hand, using 2 spray gun or more may cause the risk of inconsistent of pressure flow to each spray gun. The pressure flow in each spray gun may not be same level and reduce the performance of spray so the material pressure regulator solve this problem by adjust the pressure flow of each spray gun to be the same level, the material pressure regulator can be used for both manual gun and automatic gun. Mostly, it will be applied with automatic spray gun because there have more risk of inconsistent pressure than manual gun and spend more operating time.
The material pressure regulator support to manage the pressure flow of automatic spray gun to be use the same pressure level. The principle is 1 pressure regulator for 1 spray gun. For the amount of spray gun unit, it is depended on feeding unit performance.
Functional Principle
Example of pressure regulator (Upstream)
Example of position of pressure regulator
Functional Principle of Pressure Regulator (Upstream)
Upstream regulators control the output pressure by means of an adjustable spring load which balances the force produced by the input pressure. The spring force is adjusted by turning the handle or spindle which sets the desired output pressure. If the force resulting from the input pressure exceeds the spring force, the regulator is opened until the spring force and input pressure are balanced.
Example of back pressure regulator (Downstream)
Example of position of back pressure regulator
Functional Principle Back Pressure Regulator (Downstream)
Back pressure regulators control the input pressure by means of an adjustable spring load which balances the force produced by the input pressure. The spring force is adjusted by turning the handle or spindle which sets the desired input pressure. If the force resulting from the input pressure exceeds the spring force, the regulator is opened until the spring force and input pressure are balanced.
List of HP Material Pressure Regulator
Material High Pressure Regulator (Zinc)
Pressure Level 10 - 180 Bar
Material High Pressure Regulator (Zinc) 10 - 180 Bar
Manually controllable high-pressure regulator up to 180 bar for flow rates up to 0.8 l/min. Low-cost version from zinc-plated steel with diaphragm made of extremely resistant highly molecular polyethylene for fluids containing solvents, piston controlled.
Material Pressure Regulator is categorized by 3 types are following below;
-
T090.00A MPR 300/10-60 Bar man. CS Max. Inlet Pressure 300 Bar Range of Pressure used are 10 - 60 Bar Material outlet and inlet F-G 1/4"
-
T090.00B MPR 300/30-120 Bar man. CS Max. Inlet Pressure 300 Bar Range of Pressure used are 30 - 120 Bar Material outlet and inlet F-G 1/4"
-
T090.00C MPR 300/40-180 Bar man. CS Max. Inlet Pressure 300 Bar Range of Pressure used are 40 - 180 Bar Material outlet and inlet F-G 1/4"
Material High Pressure Regulator (Stainless)
Pressure Level 10 - 120 Bar
Material High Pressure Regulator (Stainless) 10 - 120 Bar
Manually controllable high-pressure regulator up to 120 bar for flow rates up to 3.1 l/min. Made of stainless steel with diaphragm made of extremely resistant highly molecular polyethylene suited to virtually all products.
Material Pressure Regulator is categorized by 2 types are following below;
-
T092.00AI MPR 300/10-60 SST Max. Inlet Pressure 300 Bar Range of Pressure used are 10 - 60 Bar Material outlet and inlet F-G 1/4"
-
T092.00BI MPR 300/30-120 SST Max. Inlet Pressure 300 Bar Range of Pressure used are 30 - 120 Bar Material outlet and inlet F-G 1/4"
Material High Pressure Regulator (Stainless Steel)
Pressure Level 40 - 200 Bar
Material High Pressure Regulator 40 - 200 Bar (Stainless Steel)
Manually adjustable high-pressure regulator up to 200 bar made of stainless steel, piston design with PTFE seal. Either with or without pressure gage to indicate the set product pressure.
-
3209265 MPR 40-70 man SST Max. Inlet Pressure 210 Bar Range of Pressure used are 40 - 70 Bar Material outlet and inlet F-G 3/8" and provide the max. delivery rate 1,300 CCM
-
3209434 MPR 50-200 man SST manometer Max. Inlet Pressure 210 Bar Range of Pressure used are 50 - 200 Bar Material outlet and inlet F-G 3/8" and provide the max. delivery rate 1,400 CCM
Material High Pressure Regulator (Stainless Steel)
Pressure Level 50 - 250 Bar
Material Pressure Regulator (Stainless) 50 - 250 Bar
Pneumatically controlled high-pressure regulator up to 250 bar for flow rates up to 1.0 l/min. With seat and ball made of stainless steel, not suitable for highly pigmented and abrasive products.
-
3208252 MPR 360/50-250 Bar SST Max. Inlet Pressure 360 Bar Range of Pressure used are 40 - 70 Bar Material outlet and inlet F-G 1/4"
Material High Pressure Regulator (Stainless Steel)
Pressure Level 90 - 200 Bar
Material Pressure Regulator (Stainless) 90 - 200 Bar
Manually or pneumatically adjustable high-/low-pressure regulator up to 200 bar for high flow rates. Made entirely from stainless steel with PTFE diaphragm/seal.
-
3668024 MPR-HF 360/90-200 Bar SST Max. Inlet Pressure 360 Bar Range of Pressure used are 90 - 200 Bar Material outlet and inlet F-G 3/8" with pressure gauge
List of Material High Back Pressure Regulator
.png)
High Back Pressure Regulator (Stainless Steel)
Pressure Level 40 - 200 Bar
High Back Pressure Regulator 40 - 200 Bar (Stainless Steel)
Back-pressure regulator up to 200 bar for flow rates up to 0.9 l/min. Made entirely from stainless steel, piston design with PTFE seal. Either with or without pressure gage.
-
3209123 BPR 50-200 Bar SST Max. Inlet Pressure 210 Bar Range of Pressure used are 50 - 200 Bar Material inlet F-G 1/4" and material outlet F-G 3/8"
-
3209455 BPR 50-200 Bar SST Max. Inlet Pressure 210 Bar Range of Pressure used are 50 - 200 Bar Material inlet F-G 1/4" and material outlet F-G 3/8" with pressure gauge
High Back Pressure Regulator (Stainless Steel)
Pressure Level 90 - 200 Bar
High Back Pressure Regulator 90 - 200 Bar (Stainless Steel)
Manual adjustable back-pressure regulator for high flow rates. Made of stainless steel with PTFE gasket/diaphragm.
-
3672040 BPR 360/90-200 Bar SST Max. Inlet Pressure 360 Bar Range of Pressure used are 90 - 200 Bar Material inlet F-G 3/8" and material outlet F-G 3/8"
-
2302998 BPR 360/90-200 Bar SST Max. Inlet Pressure 360 Bar Range of Pressure used are 90 - 200 Bar Material inlet F-G 3/8" and material outlet F-G 3/8" with pressure gauge
Back to
HP Accessories